Mazak CNC 画面操作アラーム エラー コード

MAZATROL MATRIXなどのマザックCNC画面操作エラーリスト

その他のマザック アラーム リストについては、次のページをご覧ください。

• マザック システム/ドライブ エラー (No.1 – No.99、No.1000 – No.1099)
• マザック CNC マシン制御エラー (No. 100 – No. 199、No. 1100 – No. 1199)
• Mazak PLC マシン制御エラー (No.200 – No.399、No.1200 – No.1399)
• マザックCNC画面操作エラー（No.400～No.499、No.1400～No.1499）
• Mazak I/O エラー (No.500 – No.599、No.1500 – No.1599)
• マザック MAZATROL プログラム エラー (No.600 – No.699、No.1600 – No.1699)
• マザック MAZATROL プログラム エラー (No.700 – No.799、No.1700 – No.1799)
• マザック EIA/ISO プログラム エラー (No. 800 – No. 899、No. 1800 – No. 1899)
• マザック EIA/ISO プログラム エラー (No. 900 – No. 999、No. 1900 – No. 1999)
• マザック干渉エラー ( No. 2100 – No. 2199 )

CNC 画面操作エラー

400

——
原因
——
アクション
——

401 不正なフォーマット

原因
入力データの形式が使用できません。
例:負のデータ入力を拒否するアイテムに負のデータが入力されました。
アクション
データキャンセルキーを押して正しいデータを入力してください。

402 不正な番号入力

原因
1.表示禁止プログラムのワーク番号を指定した。
2.入力された数値が許容範囲外です。
対処
1.表示禁止の番組（番組管理機能）に対しては、当該操作を行うことはできません。
2．クリアキーを押して正しいデータを入力してください。

403 プログラムが大きすぎます

原因
プログラムごとに 2000 行の制限を超えました。
アクション
2000 行以下になるようにプログラムを再作成してください。

404 メモリ容量超過

原因
1.メモリが加工プログラムデータの格納容量に達しているため、加工プログラムの追加作成はできません。
2.工程管理データは既に100セット蓄積されているため、追加作成は不可能である。
3. 4000セットの番組構成データが保存されているため、番組構成データの追加作成はできません。
アクション
不要な加工プログラムをメモリから消去するか、加工プログラムを外部ストレージに保存して空き領域を作り、新しい加工プログラムを作成してください。

405 プログラム番号が見つかりません

原因
ワーク番号が登録されていない番組を選択しようとしました。
対処
作品番号が登録されている番組を選択してください。

406 メモリ保護

原因
1.編集禁止プログラムに対して禁止操作(編集、消去、作品番号の再採番、氏名の入力)が行われた。
2.操作パネルの PROGRAM LOCK/ENABLE スイッチが LOCK の位置に設定されている。
3.主軸に工具をセットしたまま、工具データ表示で「工具名順」操作を行おうとしました。
対処
1.編集禁止プログラム（プログラム管理機能）に対しては当該操作を行うことはできません。
2． PROGRAM LOCK/ENABLE スイッチを ENABLE の位置に設定します。
3.スピンドルから工具を取り外してから、もう一度操作を実行してください。

407 指定されたデータが見つかりません

原因
指定された番号または文字列がプログラム内に存在しません。
対処
存在する番号または文字列を指定してください。

408 プログラム エラー

原因
加工プログラムデータ格納エリアのメモリ内容が破壊されました。
対処
対応するプログラムを削除します。

409 違法挿入

原因
プログラム データの挿入はできません。
アクション
共通ユニットの前にデータを挿入することはできません。

410 違法な削除

原因
プログラムの削除はできません。
– MAZATROL プログラムの編集中に共通ユニットを消去しようとしました。
アクション
共通ユニットを削除することはできません。
– データが存在する位置にカーソルを移動してから、プログラムを編集してください。

411 プログラム編集中の電源オフ

原因
プログラム編集中に電源が切れたため、プログラムの一部が破壊された可能性があります。
対処
対応するプログラムに不正なデータがないかチェックし、エラーが存在する場合はプログラム データを修正してください。

412 サブプログラムのネストを超えました

原因
サブプログラムのネスティングの繰り返し回数が 9 回を超えました。
対処
サブプログラムのネスティングの繰り返し回数の合計が 9 回以下になるようにプログラムを修正してください。

413 MAX.登録プログラムの数を超えました

原因
プログラム登録が利用可能な最大値 (標準:256 プログラム) を超えました。
アクション
不要なプログラムを削除またはバックアップ領域に移動するか、不要なプログラムを外部記憶装置に保存してから削除することにより、登録されているプログラムの総数を減らしてください。

414 自動計算不可

原因
周速度、送り速度の自動計算ができません。 .
–1:MAZATROLプログラムファイルオープンエラー
–2:MAZATROLプログラムファイル読み込みエラー
–3:工具材料不一致エラー(工具材料番号取得時)
–4:表面速度自動設定エラー
–5:ワーク材質上限値の基本係数に関するファイルオープンエラー
–6:ワーク材質ミスマッチエラー
–7 :表面速度データ テーブルに関するファイル オープン エラー
–8:工具材料の不一致エラー
2:ナビゲーション ファイルが見つかりません
アクション
ツール シーケンス データまたはプログラムの加工単位をチェックして修正してください。

415ミスセットGコード

原因
仕様外のGコードが指定されています。
対応
プログラム内の G コード アドレスを確認して修正してください。

416 自動処理不可

原因
加工単位データに誤りがあるため、工具の自動開発ができません。
対処
加工単位データを確認して修正してください。

417編集禁止

原因
編集が禁止されているプログラムを変更しようとしました。
対処
編集禁止のパラメータ設定を解除してからデータを修正してください。

418 EIA/ISO 変換

原因
EIA/ISO変換中に、変換元プログラムの消去、ワーク番号変更、編集を行おうとしました。または、ツールパスチェック画面を選択しようとしました。
対処
EIA/ISO変換中は、変換元プログラムの消去、ワーク番号変更、編集はできません。
ツールパスチェック画面は選択できません。

419 自動タップ処理は不可能

原因
1.タップユニットデータのタップ呼び径が正しくないため、ピッチ等の自動設定ができない。
2.パイプタップ自動設定(D95ビット0=1)でテキストファイルを参照していますが、自動設定テキストファイル(Pipescdt.txt)が間違っているかデータが無いため、自動設定機能を実行できません。 br/>アクション
1.プログラムのタッピングユニットデータ、タッピングツールシーケンスデータを確認・修正してください。
2.自動設定テキストファイル (Pipescdt.txt) を確認して修正してください。

420 の同じデータが存在します

原因
既に登録されているデータと同じデータを入力しようとしました。
1. TOOL LAYOUT表示のポケット番号。
2．加工プログラム番号（変更）
3.加工優先度番号
アクション
データ設定を確認して修正してください。

421 データが見つかりません

原因
存在しないデータを指定しようとしました。
対処
指定されたデータが存在するかどうかを確認してください。

422 メモリ保護 (I/O ビジー)

原因
I/O 操作中に、加工プログラム、工具データなどを編集または入力しようとしました。
処置
I/O 操作が完了するまで待ってから、編集または入力操作を最初からやり直してください。

423 ツールの最大数を超えました

原因
ツールのレイアウト中に、指定されたプログラムで使用されるツールの数が使用可能な最大数を超えました。
アクション
使用可能な最大工具数を超えないように、対応する加工プログラムをチェックして修正してください。

424 すべてのポケット番号が割り当てられていません

原因
すべての必要な工具にポケット番号がまだ割り当てられていないため、工具レイアウト操作を終了できません。
アクション
ポケット番号を割り当ててから、ツール レイアウト操作を終了します。

425 データがありません

原因
データが不足しているため処理できません。
1. DATA I/O画面でデータ(ワーク番号など)を指定せずにセーブまたはロードしようとした。
2.再起動操作のために入力するデータが不足しています。
アクション
データを正しく入力してください。

426 プログラム データがありません

原因
加工単位データが一部欠落しているため、工具シーケンスデータを自動展開できません。
対処
すべての加工単位データ項目にデータを入力してください。

427 メモリープロテクト (オートモード)

原因
自動操作モードで許可されていないデータを入力しようとしました。
対処
モードを手動操作モードに切り替えてから、データを入力してください。

428 メモリ プロテクト (自動操作)

原因
自動運転中の表示（工具データ表示など）で、許可されていないデータを入力しようとしました。
対処
NC 装置をリセット状態にした後、または現在のモードを別のモードに切り替えた後にのみ、許容データを入力してください。

429 測定を実行できません

原因
次の条件が満たされませんでした:
座標測定
1.自動運転中であってはならない。
2.スピンドルには工具が取り付けられている必要があります。
3.主軸に装着された工具の工具データが入力されている必要があります。
工具長測定
1.自動操作が進行中であってはなりません。
アクション
指定された条件を設定してから測定してください。

指定された 430 の違法なツール

原因
加工プログラムの作成中に、特定のプログラム ユニットで使用できないツール名をツール シーケンスで入力しようとしました。
アクション
Designate a correct tool name.

431 ILLEGAL PALLET No.

Cause
A nonexistent pallet number has been designated.
Action
Designate a correct pallet number.

432 ILLEGAL TOOL No.

Cause
A nonexistent tool number has been designated.
Action
Designate a correct tool number.

433 SAME PROGRAM EXISTS

Cause
The number of the machining program that has been designated for program reading from an external unit already exists within the NC memory.
Action
Check the number of the machining program.

434 NO ASSIGNED TOOL IN TOOL FILE

Cause
The milling tools (face-mills, end-mills, chamfering cutters, and ball end-mills) that have been designated on the machining program include a one(s) that is not yet registered in the TOOL FILE display.
Action
Register the corresponding tools in the TOOL FILE display.

435 PROGRAM CHECK NOT ALLOWED

Cause
An attempt has been made to restart on the TOOL PATH display during checking of the tool path.
Action
Interrupt the tool path checking operation before restarting.

436 UNREGISTERED TNo.

Cause
An unmeasurable tool number has been designated in the automatic tool-length (diameter) measurement mode.
Action
Designate a measurable tool number.

437 NO NOM-φ DATA IN PROGRAM

Cause
It has been found during tool layout that there is a tool without a nominal diameter in the designated program.
Action
Check if nominal diameters have been assigned to all tools registered in the designated program.

438 END UNIT NOT FOUND

Cause
The end unit is not included in the machining program.
Action
Create the end unit at the end of the program.

439 MAZATROL PROGRAM DESIGNATED

Cause
A MAZATROL program has been designated for copying purposes during EIA/ISO program editing.
Action
No MAZATROL programs can be designated for copying purposes during EIA/ISO program editing.

440 EIA/ISO PROGRAM DESIGNATED

Cause
1. The machining program that has been designated on the TOOL LAYOUT, PROCESS CONTROL or SET UP RECORD display is an EIA/ISO program.
2. An EIA/ISO program has been designated for copying purposes during MAZATROL program editing.
3. An EIA/ISO program has been designated as the source program of EIA/ISO conversion.
4. An EIA/ISO program has been designated when writing coordinate values on the MEASURE display.
Action
No EIA/ISO programs can be designated for operation on the TOOL LAYOUT, PROCESS CONTROL, SET UP RECORD or MEASURE display or during EIA/ISO conversion or MAZATROL program editing.

441 UNREGISTERED HEAD DATA

Cause
The head number that has been designated during MDI-MMS setting does not exist in the head data.
Action
Review the designated head number.

442 DATA RENEWAL NOT ALLOWED

Cause
No updates can be made to the machining program.
Action
This message may also be displayed when the NC unit is busy processing data. Press the clear key and then carry out the operation once again.

443 HELP IS NOT AVAILABLE

Cause
No help display is prepared for the line on which the cursor is placed.
Action
Refer to the Programming Manual (MAZATROL).

444 EDITING PROHIBITED AREA

Cause
During automatic operation based on the EIA MONITOR display, an attempt has been made to move the cursor to the program section whose editing was prohibited.
Action
The cursor cannot be moved to the area where editing is prohibited.

445 ILLEGAL UNIT

Cause
An attempt has been made to set tool layout data in a MAZATROL program containing an illegal unit(s).
Action
Review the program.

446 RESTART TIMES EXCEEDED

Cause
The block to be searched for at the time of restart of the EIA/ISO program does exist, but the designated number of times of reappearance of the block is too large.
Action
Check the number of times of reappearance of the block.

447 PROGRAM ERROR

Cause
A program error(s) has occurred during EIA/ISO restart search.
Action
The program being searched for includes an error(s). Perform a tool-path check upon the program contents.

448 RESTART SEARCH UNFINISHED

Cause
EIA/ISO restart searching has not been executed.
Action
Designate the restart position and press the [EIA/ISO SEARCH] button to search the intended restart position.

449 RESTART SEARCH FINISHED

Cause
An attempt has been made to carry out another search operation when EIA/ISO restart searching had already been finished.
Action
Press the reset key and then carry out the restart operation once again.

450 TOUCH SENSOR NOT IN SPINDLE

Cause
The spindle did not have a mounted touch sensor when an attempt was made to set MAZATROL coordinate measurement data on the PROGRAM (MAZATROL) display.
Action
Mount a touch sensor in the spindle before setting the data.

451 SAME MATERIAL ENTERED

Cause
The materials name that has been designated on the CUTTING CONDITION – W.-MAT/T.-MAT. display already exists.
Action
Designate a new materials name.

452 NO SHAPE DATA IN UNIT

Cause
No shape data exists in the program unit that has been designated in an attempt to make a copy of shape data.
Action
Check the contents of the program unit for which shape copying is to be made.

453 NO SHAPE DATA TO COPY IN UNIT

Cause
An attempt has been made to copy shape data whose type is not available for the particular program unit.
Action
It is not possible to copy shape data of the pallet-changing unit, index unit, or other units that do not have a shape sequence.

454 CURSOR POSITION INCORRECT

Cause
Processing not permissible for the current cursor position has been attempted.
Example 1:An attempt has been made to carry out a shape copying operation with the cursor on the tool sequence line.
Example 2:The SHAPE CHECK display has been selected on a shape sequence line not actually executed during automatic operation.
Action
Example 1:No shape data can be copied on the tool sequence line.
Example 2:Review the program.

455 SAME PROGRAM No. DESIGNATED

Cause
The machining program currently being edited has been appointed for the particular program copying operation.
Action
Copying within the same program is not possible. Check the designated program number.

456 NO TOOL IN SPINDLE

Cause
The spindle does not currently have a tool mounted on it.
Action
After mounting a tool on the spindle, carry out the particular operation once again.

457 DATA ADDRESS NOT FOUND

Cause
During creation of manual program mode unit, data setting has been attempted without addressing.
Action
During creation of the manual program mode unit, designate an address before setting data.

458 INTERFERING TOOL REGISTERED

Cause
An attempt has been made to register a tool most likely to interfere with an adjacent pocket.
Example 1:An attempt has been made to register tool data or tool change data on the TOOL DATA display.
Example 2:An attempt has been made to set such a tool on the TOOL LAYOUT display that is likely to interfere with an adjacent pocket.
Action
Select a pocket that does not cause interference with an adjacent one.

459 DISPLAY PROTECT

Cause
An attempt has been made to display a program whose display is prohibited.
Action
Display the program only after canceling the parameter setting of prohibition of display.

460 PRINTER IN OPERATION

Cause
An attempt was made on the TRACE display to perform display scaling change, material shape and tool path drawing while the hard copy is being made.
Action
After finishing the hard copy, carry out the operations.

461 PRIORITY No. OVERLAP

Cause
The same priority number is assigned to different tools.
Action
Within one process, the same priority number must not be assigned to different tools.
Change the priority number.

462 ILLEGAL PRIORITY NUMBER

Cause
The priority numbering order within a unit is not correct.
Action
The machining order within one unit has been reversed by the incorrect priority numbering.
Change the priority numbers.

463 PRIORITY No. OVERFLOW

Cause
A priority number exceeding 99 has occurred because an attempt has been made to move a priority number(s) on the PROGRAM LAYOUT display.
Action
Set priority numbers in the correct order, and then move the desired priority number(s).

464 ILLEGAL ADDRESS INPUT

Cause
An address not covered by the specifications has been designated during input of subprogram unit addresses on the PROGRAM (MAZATROL) display.
Action
Check and correct the address.
Check the specifications.

465 EIA SHAPE DATA NOT FOUND

Cause
Although an attempt has been made to draw a workpiece shape using the selected EIA/ISO program, shape data is not present in that program.
Action
Review the program.
If the program is that which has been obtained by EIA/ISO conversion output, change the setting of the bit 0 of parameter F89 to 1 and then carry out the converting operation once again.

466 INCORRECT EIA SHAPE DATA

Cause
Although an attempt has been made to draw a workpiece shape using the selected EIA/ISO program, the corresponding shape data is not correct.
Action
Review the program.

467 MEMORY PROTECT (SAMPLING)

Cause
An attempt was made during load sampling to change the axis to be monitored or the sampling time.
Action
Perform the required change after the current sampling.

468 MAINTENANCE CHECK WARNING

Cause
The target time of the items which had been set on the MAINTENANCE CHECK display has been exceeded.
Action
Carry out periodic checks, and then after completion of the checks, reset the current time of the check items of the MAINTENANCE CHECK display to zero (0).

469 TPC DATA EDIT IMPOSSIBLE

Cause
The TPC data setting is not possible for the designated unit.
Action
Check the program.

470 ILLEGAL TPC DATA

Cause
The TPC data for the unit is not correct.
After setting the TPC data, the unit machining mode has been changed.
Action
Delete the TPC data and set correct TPC data once again whenever required.

471 TPC DATA NOT FOUND

Cause
While the cursor was on a line of unit not containing TPC data on the display, the [TPC] menu key was pressed during the program list mode.
Action
Press the [TPC] menu key after shifting to the programming mode.

472 CALCULATION ERROR

Cause
1. The calculation expressions displayed in the desk calculator window includes expressions that result in a calculation failure.
2. Calculating tool lengths A and B has been attempted in spite of tool nose position storage not being completed.
Action
1. Review the calculation expressions, and correct nonexecutable sections, such as those which may include division by 0 or result in a negative number in SQRT.
2. Store the position of the tool nose.

473 FINAL POINT DATA NOT FOUND

Cause
Although the end-point data of the preceding line was not yet set in the BAR or CPY unit, the [NEXT] menu key was pressed.
Action
Press the [NEXT] menu key after setting the end-point data of the preceding line.

474 NO PROGRAM DISPLAY (TAPE MODE)

Cause
1. During tape operation mode, an attempt has been made to select the EIA MONITOR display.
2. An attempt has been made to change the operation mode to tape operation mode when the EIA MONITOR display is selected.
Action
1. During tape operation mode, programs cannot be displayed on the EIA MONITOR display.
2. Select a display other than the EIA MONITOR display before changing the operation mode to tape operation mode.

475 NO EIA/ISO OPTION

Cause
An attempt has been made to use an EIA/ISO-option related function in spite of the absence of an EIA/ISO option.
Action
An EIA/ISO-option related function cannot be used since the system has no EIA/ISO option.

476 NO OPTION

Cause
An attempt has been made to use an optional function in spite of the absence of that option.
Action
This function cannot be used since the system does not have the option for the function.

478 MEMORY PROTECT (MEASURING)

Cause
An attempt has been made to copy the coordinates data in WRITE DATA column of the MEASURE display into the designated position, while measurement using the MEASURE display is in progress.
Action
Copy the coordinates data only after the measurement has been completed.

480 CARD NOT READY

Cause
Executing the memory card I/O function in DATA I/O display mode has been attempted when a memory card was not set.
Action
Set a memory card before using the memory card I/O function.
If a memory card has been set, confirm the insertion direction of the memory card and set it again. If the alarm recurs even so, the memory card is likely to be damaged; replace the memory card and re-execute the I/O function.

481 DIRECTORY NOT FOUND

Cause
Input/output operations on a directory not present in the memory card have been attempted during memory card I/O in DATA I/O display mode.
Action
Check whether the specified directory is present.

483 SOLID DESCRIP. IMPOSSIBLE UNIT

Cause
Checking the program including the units or conditions (such as the case that angle B is set in the index unit of the initialpoint scheme) that do not allow graphics to be drawn in SOLID mode has been attempted in the SOLID mode of the TOOL PATH CHECK display.
Action
Before checking the tool path, cancel the SOLID mode or delete the unit that cannot be drawn in the SOLID mode.

484 INCORRECT SPINDLE TOOL

Cause
The [LENG-OFS TEACH] menu key has been pressed in spite of the fact that a tool not having its “Length Offset Data” item displayed in TOOL DATA display mode (for example, a turning tool) was mounted in the spindle.
Action
Check the tool mounted in the spindle.

485 INCORRECT HEAD INDEX

Cause
Executing the tool nose position storage function (TEACH) has been attempted when the head index angle displayed in TOOL DATA display mode was neither 0 degrees, 90 degrees, nor 180 degrees.
Action
Execute the tool nose position storage function (TEACH) when the head index angle is either 0 degrees, 90 degrees, or 180 degrees.

486 ILLEGAL JAW DATA

Cause
The use of the jaw shape that has been specified for the program results in interference between adjacent jaws as a result of the SOLID mode PATH CHECK.
Action
Review the jaw data or the workpiece-gripping diameter value.

487 LONG BORING BAR ADAPTER EXISTS

Cause
Assigning a tool other than an inside-diameter turning tool to the magazine pocket holding the adapter for the long boring bar has been attempted.
Action
Review the pocket number or the type of tool to be assigned.

488 MEMORY PROTECT (MAGAZINE SETUP)

Cause
Tool data updating operations (such as editing tool data, completing the layout of tools, or downloading data on the DATA I/O display) have been attempted during magazine setup.
Action
Perform tool data updating operations after completing the magazine setup operations.
Release the reverse display mode of the [MAGAZINE SETUP] menu item relating to visual tool data management.

489 CANNOT SET THREAD POSITION

Cause
An attempt was made to store the current position for re-threading (using the [THR. POS. TEACH] menu function) without the turning spindle having been rotated through at least one full turn.
Action
Rotate the turning spindle at least through one full turn beforehand to use the above menu function.

490 REGISTRATION NUMBER EXCEEDED

Cause
The data registration has exceeded its maximum value available.
An attempt was made on the TOOL FILE display to register the ninth data item of workpiece material.
Action
Delete unnecessary items to register the desired one.

491 ITEM NOT SETUP

Cause
Data registration is not yet complete.
Action
Check if all the data items are set as required.

492 CANNOT EDIT 3D DATA

Cause
Editing the CAD tool model has been attempted.
Action
The CAD tool model cannot be edited.

493 SELECT JAW TYPE

Cause
An attempt was made to set jaw dimensions without having selected the jaw type (OUT1/IN/OUT2).
Action
Select the jaw type beforehand.

494 NO TOOL SELECT (NOT MGZN TYPE)

Cause
An attempt was made to use the MDI tool selection function on the machine with a turret-type tool-post.
Action
——

495 INCORRECT CAD MODEL DATA

Cause
Registered tool model data contains imperfections (a tool model cannot be drawn with the entered data).
Action
Correct the data in the corresponding section.
Note:
During Parametric model entry…………………..The alarm-causing section is displayed.
During rotating/extruding tool model entry……Causes are displayed.
11:The entered shape has overlapping elements.
12:The entered shape is clockwise (CW).
13:The line connecting the starting and ending points overlaps some other element.

497 HEAD ANGLE INCORRECT

Cause
1. An attempt has been made to storage the tool tip position with the head not in its horizontal machining position (TOOL DATA or TOOL OFFSET display only).
2. An attempt has been made to perform MDI-MMS operation with the head not in its horizontal or vertical machining position.
Action
1. Tool tip position storage (tool length measurement) is possible only with the head in its horizontal machining position.
2. MDI-MMS is possible only with the head in its horizontal or vertical machining position.

498 NO HEAD DATA

Cause
Offset data for the selected head is not registered on the HEAD OFFSET display.
Action
Check if the selected head data is registered on the HEAD OFFSET display.

499 ILLEGAL HEAD TYPE

Cause
An attempt has been made to perform tool tip position storage on the TOOL DATA or TOOL OFFSET display during use of the horizontal type of head.
Action
To perform tool tip position storage for tool length measurement, mount a vertical head or a cover.

1400 SYSTEM ERROR

Cause
An internal trouble has occurred in the system.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1401 FILE OPEN ERROR

Cause
Trouble has occurred in opening a file from the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1402 FILE READ ERROR

Cause
Trouble has occurred in reading a file on the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1403 FILE WRITE ERROR

Cause
Trouble has occurred in writing a file on the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1404 MEMORY PROTECT (DATA IN USE)

Cause
It was attempted to edit jaw shape data of the machining program currently selected.
Action
Change the selection of the program to edit the required data.

1405 FILE SIZE ERROR

Cause
The size of the loaded file is not correct.
Action
The file in question might be destroyed.
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1406 LOW MEMORY

Cause
Memory size currently available is too small.
Action
Exit all the unnecessary applications to make the best of the NC ones.
If the alarm is caused again, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1407 FILE CREATION ERROR

Cause
Creating a file and folder on the hard disk was not successful.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1408 DATA TRANSFER ERROR

Cause
Data transfer to the NC was not successful.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1409 MILLING ONLY SELECTED

Cause
The designated function is not available for a program of initial-point scheme (ONLY MILL).
Action
Use the function for a program of another scheme.

1410 MILL &TURN (WPC) SELECTED

Cause
The designated function is not available for a program of workpiece scheme (MILL &TURN) with WPC setting.
Action
Use the function for a program of another scheme.

1411 MILL &TRN (Z-OFS) SELECTED

Cause
The designated function is not available for a program of workpiece scheme (MILL &TURN) with Z-offset setting.
Action
Use the function for a program of another scheme.

1412 INCORRECT G-CODE

Cause
The designated function is not available for the G-code system selected by the F30 parameter.
Action
Correct the program, or change the F30 setting.

1413 INCORRECT RUNNING MODE

Cause
The designated function is not available for the current mode of operation.
Action
Change the operation mode.

1414 PROGRAM WRITING

Cause
Storing a program on the hard disk was not successful.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1415 ZERO CALCULATED TOOL LENGTH

Cause
The LENGTH A item of the tool is set to zero (0).
Action
Check the settings of tool length or tool set data and, if required, measure the tool in question again.

1416 CANNOT INDEX TOOL

Cause
The tool currently indexed on the turret is not appropriate.
Action
Index an appropriate tool beforehand.

1417 PARAMETER ERROR

Cause
The setting in a parameter is not correct.
Action
Check and correct the parameter setting with reference to the codes displayed in parentheses.

1418 CANNOT USE LOWER TURRET

Cause
The current selection of the headstock to which the lower turret is subordinate is not correct.
Action
Change over the headstock selection concerned.

1420 FILE SIZE LIMIT EXCEEDED

Cause
The size of the file is too large for new data to be written in it.
Action
Delete the file, or rename the file.

1422 PROGRAM LAYOUT ERROR

Cause
Creating the data for turret-by-turret display of program layout was not successful.
Action
Change the display mode.

1423 TOOL PATH CHECK NOT COMPLETE

Cause
Since the program has not yet undergone tool path check, the VISUAL TOOL MANAGEMENT display cannot perform calculations for indicating the spare tools to be additionally provided for the machining operation with the program.
Action
Execute the function for tool path check on the program.

1424 BARRIER INFORMATION NOT SET

Cause
In the program-listing mode the [BARRIER INFORM.] menu function is selected without any barrier data being registered.
Action
Select the program-creating mode before pressing the [BARRIER INFORM.] menu key.

1425 ILLEGAL SETUP DATA

Cause
The setup data are not correct.
Action
Make a copy of the program in question on the PROGRAM FILE display, and prepare the setup data for the program copied.

1426 NO PROG LAYOUT FOR THIS PROCESS

Cause
The current process has no program layout information provided.
Action
Press the menu selector key to select a process with program layout data, or select the display mode for all processes.
Alternatively, select a process with program layout data on the PROGRAM (MAZATROL) display or PROCESS CONTROL display and then call up the PROGRAM LAYOUT display from there.

1427 3D INTERFRNCE CHECK MODEL ERROR

Cause
3D remodeling of the workpiece, fixture, or tool has failed.
Action
Modify the entered data.
Confirm the model.

1428 NOT POCKET FOR LONG BORING BAR

Cause
Assigning the long boring bar to a section not defined as a special pocket for the long boring bar has been attempted during the “Layout Completion” operations on the VISUAL TOOL MANAGEMENT display.
Action
Assign the long boring bar to the special pocket.

1429 INCORRECT SELECT TOOL

Cause
Tool setup auto-setting for a tool not capable of using the tool setup auto-setting function (e.g., a magazine tool or a tool facing the No. 1 turning spindle) has been attempted on the TOOL DATA display.
Action
Apply the tool setup auto-setting function only to a turret tool facing the No. 2 turning spindle.

1430 NOT ACTIVE PROGRAM

Cause
This alarm indicates that the machine-operating program and the program selected on the PROGRAM (MAZATROL) display differ during execution of the workpiece transfer storage function on the PROGRAM (MAZATROL) display.
Action
Match the machine-operating program and the program selected on the PROGRAM (MAZATROL) display.

1431 AUTO SET ERROR

Cause
Tool data
Action

1432 NO SELECT TOOL MODEL

Cause
The tool model to be copied/erased/renamed is not selected.
Action
Select the appropriate tool model before performing the copy/erasure/name change.

1433 SAME TOOL MODEL EXISTS

Cause
A registered tool model has been specified during the copy/name change.
Action
Specify an unregistered name.